Коды ошибок Ricoh Aficio SP150.

Коды ошибок Ricoh Aficio SP150 (SP 150)

Код ошибки SC	Наиболее часто встречающиеся ошибки, весь список ошибок см. ниже
	При возникновении ошибки (SC code), индикатор статуса на виртульной панели становится красным (Error). В строке сообщений появляется дополнительная информация.
202	Ошибки блока лазера.
203
204
220
491	Перегрузка или неисправность высоковольтного блока.
501	Прижимная пластина в лотке подачи бумаги не двигается. Управляется электромагнитной муфтой, контролируется датчиком
520	Перегрузка или неисправность главного мотора.
530	Неисправность вентилятора охлаждения.
541	Неполадки с термозакреплением. Возможны неисправности элементов блока закрепления...
542
543
544
545
559
547	Температура внутри блока по показаниям датчика меньше -30'C или больше 105'C.
560	Напряжение сети меньше 140В.
668	Ошибка главной платы
1001	Ошибка сканера

Code: SC101
Description: Exposure lamp error
The standard while level was not detected properly when scanning the white plate.
Causes: • Exposure lamp defective • Exposure lamp stabilizer defective • Exposure lamp connector defective • Dirty scanner mirror or scanner mirror out of position • SBU board defective • SBU connector defective • Lens block out of position

Code: SC120
Description: Scanner home position error 1
The scanner home position sensor does not detect the off condition during initialization or copying.
Causes: • Scanner home position sensor defective • Scanner drive motor defective • Scanner home position sensor connector defective • Scanner drive motor connector defective • IOB board defective

Code: SC121
Description: Scanner home position error 2
The scanner home position sensor does not detect the on condition during initialization or copying.
Causes: • Scanner home position sensor defective • Scanner drive motor defective • Scanner home position sensor connector defective • Scanner drive motor connector defective • IOB board defective

Code: SC122
Description: Scanner home position error 3
The scanner home position sensor detects the on condition while the scanner is returning to the home position.
Causes: • Scanner home position sensor defective • Scanner drive motor defective • Scanner home position sensor connector defective • Scanner drive motor connector defective • IOB board defective

Code: SC123
Description: Scanner home position error 4
The scanner home position sensor does not detect the on condition after the scanner returns to the home position.
Causes: • Scanner home position sensor defective • Scanner drive motor defective • Scanner home position sensor connector defective • Scanner drive motor connector defective • IOB board defective

Code: SC192
Description: Automatic SBU adjustment error
An error is detected during automatic SBU adjustment (SP4-903)
Causes: • SBU defective • BICU board defective • Exposure lamp stabilizer defective • Exposure lamp defective • Dirty white plate

Code: SC194
Description: IPU White Level Detection Error
The level of the white standard pattern detected by the IPU chip (on the BICU board) is too low.
Causes: • Exposure lamp defective • BICU board defective • Incorrect position of the white standard pattern • Dirty white plate • SBU board defective

Code: SC302
Description: Charge roller current leak
A charge roller current leak signal is detected.
Causes: • Charge roller damaged • Charge high voltage supply board defective • Poor connection of the PCU

Code: SC320
Description: Polygon motor error
The polygon motor does not reach its operating speed within 10 seconds after the polygon motor on signal, or the lock signal is not detected for more than 200 ms continuously during operation.
Causes: • Polygon mirror motor defective • Poor connection between the polygon mirror motor driver and the BICU board • BICU board defective

Code: SC321
Description: No laser start signal (F-GATE error)
The laser writing signal (F-GATE) is still not LOW when the laser writing area +5 mm has passed since the laser writing start position on the drum.
Causes: • BICU board defective • EMB (Copier feature expander) board defective • The fax controller or printer controller has a poor connection. • Fax controller or printer controller defective

Code: SC322
Description: Laser synchronization error
The main scan synchronization detector board cannot detect the laser synchronization signal for more than 5 consecutive 100 ms intervals.
Causes: • Poor connection between the laser synchronization detector board and the BICU board • Laser synchronization detector board out of position • Laser synchronization detector board defective • BICU board defective • LD unit defective

Code: SC324
Description: LD drive current over
The LD drive board applies more than 100 mA to the LD.
Causes: • LD unit defective (not enough power, due to aging) • Poor connection between the LD unit and the BICU board • BICU board defective

Code: SC390
Description: TD sensor error 1
The TD sensor outputs less than 0.5V or more than 4.0V 10 times consecutively during copying.
Causes: • TD sensor abnormal • Poor connection of the PCU

Code: SC391
Description: Development bias leak
A development bias leak signal is detected.
Causes: • Poor connection of the PCU • High voltage supply board defective

Code: SC392
Description: TD sensor initial setting error
TD sensor output voltage falls out of the adjustment range (2.0 +- 0.2 V) after the TD sensor initial setting has been finished.
Causes: • Someone forgot to remove the toner seal of the PCU • ID sensor defective • TD sensor abnormal • Drum does not turn • Development roller does not turn • Poor connection of the PCU

Code: SC401
Description: Transfer roller leak error 1
A transfer roller current leak signal is detected. The current feedback signal for the transfer roller is not detected.
Causes: • High voltage supply board defective • Poor connection of the PCU • Transfer/separation unit set incorrectly • Transfer roller damaged

Code: SC402
Description: Transfer roller leak error 2
A transfer roller current leak signal is detected. The current feedback signal for the transfer roller is not detected.
Causes: • High voltage supply board defective • Poor connection of the PCU • Transfer/separation unit set incorrectly • Transfer roller damaged

Code: SC411
Description: Separation bias leak error
A separation bias leak signal is detected.
Causes: • High voltage supply board defective • Poor connection of the PCU • Discharge plate defective

Code: SC500
Description: Main motor lock
A main motor lock signal is not detected for more than 500 ms after the main motor starts to rotate, or the lock signal is not detected for more than 500 ms during rotation after the last signal.
Causes: • Too much load on the drive mechanism • Main motor defective

Code: SC501
Description: 1st paper tray lift motor malfunction
The paper lift sensor is not activated after the tray lift motor has been on for 18 seconds.
Causes: • Paper lift sensor defective • Tray lift motor defective • Too much load on the drive mechanism • Poor tray lift motor connection

Code: SC502
Description: 2nd paper tray lift motor malfunction
The paper lift sensor is not activated after the tray lift motor has been on for 18 seconds.
Causes: • Paper lift sensor defective • Tray lift motor defective • Too much load on the drive mechanism • Poor tray lift motor connection

Code: SC503
Description: 3rd paper tray lift motor malfunction (optional paper tray unit)
The paper lift sensor is not activated after the tray lift motor has been on for 18 seconds.
Causes: • Paper lift sensor defective • Tray lift motor defective • Too much load on the drive mechanism • Poor tray lift motor connection

Code: SC504
Description: 4th paper tray lift motor malfunction (optional paper tray unit)
The paper lift sensor is not activated after the tray lift motor has been on for 18 seconds.
Causes: • Paper lift sensor defective • Tray lift motor defective • Too much load on the drive mechanism • Poor tray lift motor connection

Code: SC506
Description: Paper tray unit main motor lock (optional paper tray unit only)
A motor lock signal is not detected for more than 1.5 s or the lock signal is not detected for more than 1.0 s during rotation.
Causes: • Paper tray unit motor defective • Too much load on the drive mechanism

Code: SC507
Description: Tandem tray lift error (optional LCT)
The lower limit sensor is not activated after the paper tray lift motor has been on to lower the tandem tray for 8 seconds.
Causes: • Paper tray lift motor defective • Lower limit sensor defective • Too much load on the drive mechanism

Code: SC508
Description: Rear fence drive error (optional LCT)
The return position sensor is not activated after the rear fence drive motor has been on to lower the tandem tray for 8 seconds.
Causes: • Rear fence motor defective • Return position sensor defective • Too much load on the drive mechanism

Code: SC509
Description: Side fence drive error (optional LCT)
The side fence positioning sensor is not activated for more 3 seconds when the paper stack in the left tray is moved to the right tray. The side fence close sensor is not activated for more 3 seconds after moving the paper stack to the right tray.
Causes: • Side fence motor defective • Side fence position sensor defective • Side fence close sensor defective • Too much load on the drive mechanism

Code: SC541
Description: Fusing thermistor open
The fusing temperature detected by the thermistor was below 55 °C for 15 seconds or below 75 °C for 20 seconds.
Causes: • Fusing thermistor defective or out of position • Fusing lamp open • Fusing thermofuse open • Power supply board defective • Poor connection of the fusing unit

Code: SC542
Description: Fusing temperature warm-up error
The fusing temperature does not reach 155 °C within 60 seconds after the main switch is turned on.
Causes: • Fusing thermistor defective or out of position • Fusing lamp open • Fusing thermofuse open • Power supply board defective • Poor connection of the fusing unit

Code: SC543
Description: Fusing overheat error
A fusing temperature of over 231°C is detected for 1 second by the fusing thermistor.
Causes: • Fusing thermistor defective • Power supply board defectivee mechanism

Code: SC544
Description: Fusing low temperature error
A fusing temperature of lower than 100°C is detected for 1 second by the fusing thermistor.
Causes: • Fusing thermistor defective • Power supply board defective • Poor connection of the fusing unit

Code: SC546
Description: Unstable fusing temperature
Fusing temperature more than 60 °C: The fusing temperature does not rise 2°C or more within 6 seconds after the fusing lamp has been on. Fusing temperature 60 °C or less: The fusing temperature does not rise 2°C or more during a 6 second interval (the 6 s timer starts 14 s after the fusing lamp turned on).
Causes: • Thermistor defective • Poor connection of the fusing unit • Power supply unit defective

Code: SC547
Description: Zero cross signal malfunction
Zero cross signals are not detected within a certain period.
Causes: • Power supply board defective • IOB defective • BICU defectivechanism

Code: SC590
Description: Exhaust fan motor error
The CPU detects an exhaust fan lock signal for more than 3.5 seconds.
Causes: • Poor connection of the exhaust fan motor • Too much load on the motor drive

Code: SC610
Description: Communication error between IOB and duplex unit
The IOB cannot communicate with the duplex unit properly.
Causes: • Poor connection between the IOB and duplex unit • IOB defective • Duplex control board defective

Code: SC620
Description: Communication error between IOB and ADF
The IOB cannot receive a response from the ADF main board for 4 seconds or more.
Causes: • Poor connection between the IOB and ADF main board (DF connector) • ADF main board defective • IOB defective

Code: SC691
Description: Communication error between BICU and fax controller
The BICU board cannot communicate with the fax controller properly.
Causes: • Poor connection between the BICU board and the fax controller • BICU board defective • Fax controller defective

Code: SC692
Description: Communication error between BiCU and printer controller
The BICU board cannot communicate with the printer controller properly.
Causes: • Poor connection between the BICU board and the mother board. • Poor connection between the mother board and the printer controller • BICU board defective • Printer controller defective • Mother board defective

Code: SC694
Description: Communication error between BICU and scanner controller
The BICU board cannot communicate with the scanner controller properly.
Causes: • Poor connection between the BICU board and the mother board. • Poor connection between the mother board and the scanner controller • BICU board defective • Scanner controller defective • Mother board defective

Code: SC696
Description: Communication error between IOB and finisher
The IOB cannot communicate with the finisher properly.
Causes: • Poor connection between the IOB and finisher • IOB defective • Finisher main board defective

Code: SC722
Description: Finisher jogger motor error
1) The finisher jogger H.P sensor remains de-activated for a certain time when returning to home position. 2) The finisher jogger H.P sensor remains activated for a certain time when moving away from home position.
Causes: • Jogger H.P sensor defective • Jogger motor defective

Code: SC725
Description: Finisher stack feed-out motor error
The stack feed-out belt H.P sensor does not activate within a certain time after the stack feed-out motor turned on.
Causes: • Stack feed-out H.P sensor defective • Stack feed-out motor defective

Code: SC726
Description: Finisher shift motor error
Tray shift does not finish within a certain time after the shift motor turned on.
Causes: • Shift motor defective • Shift tray half-turn sensor defectivefective

Code: SC730
Description: Finisher stapler position motor error
1) The stapler does not return to its home position within a certain time after the stapler motor turned on. 2) The stapler H.P sensor does not activate within a certain time after the stapler motor turned on.
Causes: • Stapler motor defective • Stapler H.P sensor defective • Poor stapler motor connection

Code: SC733
Description: Finisher stack feed-out motor error
The stack feed-out belt H.P sensor does not activate within a certain time after the stack feed-out motor turned on.
Causes: • Stack feed-out H.P sensor defective • Stack feed-out motor defective

Code: SC734
Description: Finisher lift motor error
The stack height sensor does not activate within a certain time after the shift tray lift motor turned on.
Causes: • Shift tray lift motor defective • Stack height sensor defectivective

Code: SC735
Description: Finisher exit guide plate motor error
The exit guide plate open sensor or exit guide plate HP sensor does not activate within a certain time after the exit guide plate motor turned on.
Causes: • Exit guide plate motor defective • Exit guide plate HP sensor defective • Exit guide plate open sensor defective

Code: SC750
Description: Intp2ange unit connection error
The IOB cannot communicate with the intp2ange unit properly when the duplex unit is installed.
Causes: • Poor connection between the IOB and intp2ange unit • IOB defective

Code: SC751
Description: Bridge unit connection error
The IOB cannot communicate with the bridge unit properly when the finisher is installed.
Causes: • Poor connection between the IOB and bridge unit • IOB defectivective

Code: SC752
Description: Finisher connection error
The IOB cannot communicate with the finisher properly when the bridge unit is installed.
Causes: • Poor connection between the finisher and bridge unit • IOB defective

Code: SC760
Description: ADF gate abnormal
The ADF Gate signal line between the ADF main board and the IOB is disconnected.
Causes: • ADF main board defective • Input/output board defective • Por connection (ADF Gate line) between the ADF main board and the IOB.

Code: SC770
Description: Shift tray motor error (optional shift tray unit)
The shift tray half-turn sensor is not activated within a certain time after the shift tray motor turned on.
Causes: • Shift tray motor defective • Shift tray half-turn sensor defective

Code: SC900
Description: Total counter error
Causes: • NVRAM defective

Code: SC901
Description: Mechanical Total Counter
The mechanical total counter is not working properly.
Causes: • Mechanical total counter defective • IOB defective • Disconnected mechanical total counter

Code: SC921
Description: MSU hardware error
The hardware of the MSU is defective.
Causes: • EMB (Copier feature expander) defective • BICU defective defective

Code: SC980
Description: Program loading error
The program cannot load properly.
Causes: • The connection between the BICU and the IC board is poor. • BICU board defective • IC board or the program defective NOTE: This SC should be cleared by trying to download again from an IC card.

Code: SC981
Description: NVRAM clear error
Causes:

Code: SC990
Description: Communication error between BICU and IOCSS board
The BICU board cannot communicate with the IOB.
Causes: • The connection between the BICU board and the IOB is poor. • BICU board defective • IOB defective

Code: SC999
Description: Program version error
An incorrect type of main software was downloaded.
Causes: • The main software for another machine was downloaded to this machine.

ricoh sp 150 горит красным, ricoh sp 150 горит красный индикатор - ЗАКОНЧИЛСЯ ТОНЕР, НУЖНО ЗАПРАВИТЬ КАРТРИДЖ.

Ricoh Sp150 ошибка Sc 202, 203, 204, 220, 491, 501, 520, 530, 541, 542, 543, 544, 545, 559, 547, 560, 668, 1001
Коды ошибок Ricoh Aficio SP150 ошибка 203 сброс ошибки Ricoh 150 сброс Ricoh SP150 код ошибки, сброс Ricoh SP150 как сбросить ошибку