Коды ошибок HP LaserJet Pro m225 MFP
Код ошибки
|
Дисплей
|
Описание
|
Устранение проблемы
|
|
13.0000
|
13.0000
|
Paper jam
|
|
|
20.0000
|
20.0000
|
Memory out
|
|
|
21.0000
|
21.0000
|
Page misfeed or mispick
|
|
|
41.2000
|
41.2000
|
Beam detect malfunction
|
|
|
41.3000
|
41.3000
|
Unexpected size
|
|
|
49
|
49 Error
|
The product has experienced a firmware error.
|
1. Press the power button to turn the product off. 2. If a surge protector is being used, remove it. Plug the power cord directly into a wall
outlet. 3. Wait at least 30 seconds, turn the product on, and then wait for the product to initialize. 4. If the error persists, disconnect and
then reconnect the FFCs and the connectors on the formatter PCA. 5. If the error persists, replace the formatter PCA.
|
|
50.0000
|
50.0000
|
Fuser error
|
|
|
50.1000
|
50.1000
|
Low fuser temperature error
|
|
|
50.2000
|
50.2000
|
Slow fuser error
|
|
|
50.3000
|
50.3000
|
High fuser temperature error
|
|
|
50.4000
|
50.4000
|
Fuser drive circuit error
|
|
|
50.7000
|
50.7000
|
Fuser open error. Low sub-thermistor fuser error. High sub-thermistor fuser error
|
|
|
50.X
|
50.X Fuser Error
|
The product has an internal hardware error.
|
1. Press the power button to turn the product off.2. If a surge protector is in use, remove it. Connect the power cord directly into a wall
outlet.3. Wait at least 25 minutes, turn the product on, and then wait for the product to initialize.4. If the error persists, reconnect J101
and J552 on the engine controller PCA.5. If the error persists, check the power source. Make sure that the power source meets the minimum
system requirements (40Hz to 70Hz).6. If the error persists, replace the fuser.7. If the error persists, replace the engine controller PCA.
|
|
51.0000
|
51.0000
|
Beam detect or laser error
|
|
|
51.2000
|
51.2000
|
Black scanner laser error (inline devices only)
|
|
|
51.XX
|
51.XX Error
|
The printer has experienced an internal hardware error. The product may display the following message: 51.20 Black laser scanner error
|
Turn off the power by using the power switch, wait at least 30 seconds, and then turn on the power and wait for the printer to initialize. If a
surge protector is used, remove it. Plug the printer directly into the wall socket. Use the power switch to turn on the printer. If the message
persists, contact HP support.
|
|
52.0000
|
52.0000
|
Engine laser scanner error
|
|
|
54.0100
|
54.0100
|
Environmental sensor error
|
Verify that the DC controller connectors are firmly connected. If the error persists, replace the temperature/humidity sensor. If the error
persists, replace the DC controller.
|
|
54.0600
|
54.0600
|
Density sensor error
|
Verify that the cables between the DC controller is firmly connected.
|
|
54.1100
|
54.1100
|
Black density out of range
|
If the error persists, replace the color misregistration sensor.
|
|
54.1200
|
54.1200
|
Black density measurement abnormality
|
If the error persists, replace the DC controller.
|
|
54.1599
|
54.1599
|
Black CPR pattern cannot be read
|
1. Turn off the power by using the power switch, and then wait at least 30 seconds.2. Turn on the power and wait for the product to initialize.
If the error persists, verify that the cables between the color misregistration sensor and the DC controller are firmly connected. If the error
persists, replace the color misregistration sensor. If the error persists, replace the toner cartridge tray. If the error persists, replace the
DC controller.
|
|
54.1600
|
54.1600
|
Black CPR pattern cannot be read
|
1. Turn off the power by using the power switch, and then wait at least 30 seconds.2. Turn on the power and wait for the product to initialize.
If the error persists, verify that the cables between the color misregistration sensor and the DC controller are firmly connected. If the error
persists, replace the color misregistration sensor. If the error persists, replace the toner cartridge tray. If the error persists, replace the
DC controller.
|
|
54.2100
|
54.2100
|
Beam detect (BD) error
|
If the error persists, replace the DC controller. If the error persists, replace the product.
|
|
54.2500
|
54.2500
|
Top-of-page sensor error
|
Verify that the DC controller connectors are firmly connected. If the error persists, replace the DC controller.
|
|
54.XX
|
54.XX
|
The printer has experienced an error with one of the internal sensors. The product may display one of the following messages:• 54.18 Black
toner level sensor error• 54.19 TOP sensor error• 54.1200 Black density measurement abnormality• 54.1500 Black CPR pattern cant be read• 54.21
BD errors
|
Turn off the power by using the power switch, wait at least 30 seconds, and then turn on the power and wait for the printer to initialize. If a
surge protector is used, remove it. Plug the printer directly into the wall socket. Use the power switch to turn on the printer. If the message
persists, contact HP support.
|
|
55.3000
|
55.3000
|
Engine-formatter communication error
|
|
|
55.4000
|
55.4000
|
Engine communication timeout error
|
|
|
55.X
|
55.X Error
|
The printer has experienced an internal error. The printer may experience one of the following errors:• 55.0 DC controller communication error•
55.0601 DC controller NVRAM data error• 55.0602 DC controller NVRAM access error• 55.1 DC controller memory error
|
Turn off the power by using the power switch, wait at least 30 seconds, and then turn on the power and wait for the printer to initialize. If a
surge protector is used, remove it. Plug the printer directly into the wall socket. Use the power switch to turn on the printer.
|
|
57
|
57 Fan Error
|
The product has a general fan error.
|
1. Press the power button to turn the product off.2. If a surge protector is in use, remove it. Connect the power cord directly into a wall
outlet.3. Wait at least 30 seconds, turn the product on, and then wait for the product to initialize.4. If the error persists, reconnect the
J1103 connector on the duplex connector PCA.5. If the error persists, replace the main fan.
|
|
57.0000
|
57.0000
|
Fan motor error
|
|
|
57.0600
|
57.0600
|
Fan motor error
|
|
|
59.X
|
59.X Error
|
The printer has experienced a problem with one of the motors. The product may display one of the following errors:• 59.3 Fuser motor startup
error• 59.4 Fuser motor rotation error• 59.50 Image drum motor startup error - black• 59.73 Developer motor startup error• 59.83 Developer
motor rotation error• 59.C0 Developer motor rotation error• 59.F0 Transfer alienation failure
|
Turn off the power by using the power switch, wait at least 30 seconds, and then turn on the power and wait for the printer to initialize. If a
surge protector is used, remove it. Plug the printer directly into the wall socket. Use the power switch to turn on the printer.
|
|
79
|
79 Error
|
The product has experienced a firmware error
|
1. Press the power button to turn the product off.2. If a surge protector is in use, remove it. Connect the power cord directly into a wall
outlet.3. Wait at least 30 seconds, turn the product on, and then wait for the product to initialize.4. If the error persists, disconnect and
then reconnect the FFCs and the connectors on the formatter PCA.5. If the issue persists, replace the formatter PCA.
|
мфу HP Pro m225 MFP, HP M225, ошибка 13.0000,
20.0000,
21.0000,
41.2000,
41.3000,
49,
50.0000,
50.1000,
50.2000,
50.3000,
50.4000,
50.7000,
50.X,
51.0000,
51.2000,
51.XX,
52.0000,
54.0100,
54.0600,
54.1100,
54.1200,
54.1599,
54.1600,
54.2100,
54.2500,
54.XX,
55.3000,
55.4000,
55.X,
57,
57.0000,
57.0600,
59.X,
79,
как сбросить ошибку hp m225,
коды ошибок HP Pro m225, MFP, HP LaserJet Pro m225, HP M225, HP M225 ошибка
|
