ОргТехСервис
Главная | Каталог | Услуги | Наши клиенты | Контакты | Техподдержка | Полезная информация


Коды ошибок мфу Canon iR2200/iR2800/iR3300

Код ошибкиСуб
код		Описание
E0000000The reading of the main thermistor does not reach 30oC 1 sec after the main power switch is turned on. Or, it does not reach 70oC 2 sec thereafter
E0010000The main thermistor detects 250oC or higher
0001The main thermistor or the sub thermistor detects overheating (hardware circuit detection)
0002The sub thermistor detects about 295oC or higher
E0020000The temperature of the fixing film is as follows:
  • has exceeded 100oC, but does not reach 115oC within 1 sec thereafter.
  • has exceeded 140oC, but does not reach 150oC within 1 sec thereafter.
  • has exceeded 160oC, but does not reach 165oC within 1 sec thereafter
    • E0030000The main thermistor reading is lower than 140oC when paper is moved
    0001Low fixing temperature detection after standby (by sub thermistor)
    E0070000An error in the rotation of the fixing film is detected.
    The reading of the main thermistor is 100oC or higher and, in addition, the fixing film sensor does not detect the rotation of the film for 6 sec or more while the fixing motor is driven
    E0100000After the main motor drive signal is generated, the clock signal does to arrive within 1.3 sec
    E014000After the fixing motor drive signal is generated, the clock signal does not arrive within 1.3 sec
    E0190000The waste toner case is full of waste toner
    E0320001The DA unit connection is disconnected (after connection).
    E0510000At start-up, home position is not detected when the horizontal registration assembly is moved 100 mm in the direction of home position
    E0640000The presence of a high-voltage error is communicated by the composite power supply PCB (The output for primary charging, developing, or transfer has deviated from a specific level of voltage)
    E1000001The BD signal is not detected 10 times or more within 10 msec in 5 msec after the generation of the laser drive signal
    0001The BD signal is not detected 10 times or more within 10 msec in 5 msec after the generation of the laser drive signal
    0002While the laser is ON, the BD signal cycle is outside a specific range 20 times or more continuously
    0003While the laser is ON, the horizontal sync signal cycle is outside a specific range 20 times or more
    E1100000The motor ready signal does not arrive within 15 sec after the laser scanner motor drive signal is generated
    E2020001The scanner home position sensor does not go OFF when the scanner is moved forward by 40 mm
    0002The scanner home position sensor does not go ON when the scanner is moved reverse 450 mm
    E2040001While an original is being read, the image leading edge signal does not arrive from the ADF
    E2200001A fault is detected on the inverter PCB for the scanning lamp
    E2250000A specific level cannot be attained for the signal during CCD gain correction at power-on
    0002The edge gain correction level is different from the correction level for the preceding sheet by a specific level or more
    E2400000A fault occurs in communication between the CPU of the main controller PCB and the CPU of the DC controller PCB
    E2430000A fault occurs in the communication between the CPU of the control panel PCB and the CPU of the main controller PCB
    E2480001A difference is discovered between the ID in EEPROM read when the main power switch is turned on and the ID in ROM upon comparison
    0002The data read does not match the data written to EEPROM
    0003A difference is discovered between the ID of EEPROM and the ID of ROM upon comparison while writing data
    E2610000 The intervals of zero-cross signals deviate from the tolerance range while the fixing heater is supplied with power
    E3020001 During shading, the shading processing does not end on the reader controller PCB after 1 sec
    0002During stream reading, the edge white addition processing does not end on the rear controller PCB after 10 sec
    E315-Any of the following is true in the image processing by the main controller:
  • The image data has a fault
  • The encoding/decoding operation for image data has a fault
  • The image processing element of the main controller PCB has a fault
    • E6010000When an image is transferred between the main controller PCB and the HDD, the main controller PCB detects a fault in control information
    0001When an image is transferred between the main controller PCB and the DC controller PCB, the DC controller PCB detects a fault in the control information
    E6020001A mounting fault of the HDD is detected when the HDD is started up from the BOOT ROM
    0002A data read fault of the HDD is detected when the HDD is started up from the BOOT ROM
    E6040000 A fault is detected in the image memory
    E6050001 A fault is detected in the battery for the image memory
    E6060001 A mounting fault of the HDD is detected when the HDD is started up from the BOOT ROM
    E6740000 A faulty occurs in the communication between the fax PCB and the main controller PCB
    E6770001 A fault occurs it the combination between any of the printer boards (accessories) and the main controller PCB
    E7100001 When the main power is turned on, the communication IC (IPC) on the reader controller PCB cannot be initialized
    0002 When the main power is turned on, the communication IC (IPC) on the DC controller PCB cannot be initialized
    0003 When the main power is trend on, the communication IC (IPC) on the main controller PCB cannot be initialized
    E7110001 Data is written to the error register of the communication IC (IPC) on the reader controller PCB four times or more within 1.5 sec
    0002 Data is written to the error register of the communication IC (IPC) on the DC controller PCB four times or more within 2 sec
    0003Data is written to the error register of the communication IC (IPC) on the main controller PCB four times or more within 2 sec
    E7120001The communication is not resumed 3 sec or more after data has been written to the error register of the communication IC (IPC) on the ADF controller PCB
    0002The transmission bit is not enabled 10 sec or more in the sync register of the communication IC (IPC) on e reader controller PCB
    E7130000The communication with the finisher is not resumed 3 sec or more after it is disrupted
    E7160000The ID signal is not detected within a specific period of time after the presence of a pedestal is detected
    E7190000Erroneous communication with card reader (serial communication)
    0002Erroneous communication with coin vender (serial communication)
    E7170001The communication with the DA unit is not resumed 3 sec or more after it is disrupted
    E7190001The communication between the Card Reader-C1 or the coin vendor and the main controller PCB is disrupted
    E7320001 A fault is detected by the main controller PCB in the communication between reader controller PCB and the main controller PCB
    E7330001 A fault is detected by the main controller PCB in the communication between the DC controller PCB and the main controller PCB
    E7370000During self diagnosis at power-on, the DRAM check finds a fault in the main controller PCB
    E7400001At power-on, the LAN card has a fault
    0002The MAC address has a fault
    0003The LAN card cannot be read
    E7410000 The PCI bus has a fault
    E7430000 The reader controller PCB detects a fault in the communication between the main controller PCB and the reader controller PCB
    E7440000 The Boot ROM on the main controller PCB and the system software are for different models or are of different types
    E8030000 The 24V output from the composite main power supply PCB is absent for 1 sec or more
    E805 The clock signal is absent for 5 sec or more after the fan drive signal has been generated. The detail codes of the fans in question are as follows:
    0001developing fan (FM1)
    0002fixing fan (FM2)
    0003curl reducing fan (FM4)
    0004curl reducing fan (FM5)
    0005electrical unit fan (FM3)
    E9010000The motor ready signal does not arrive within 1.3 sec after the pedestal main motor drive signal is generated
    ADF Error Codes
    E4200001 When the power switch of the host machine is turned on, the back-up data from the EEPROM cannot be read or the data that has been read has a fault
    E4210001 The back-up data cannot be written to the EEPROM, or the data that has been written has a fault
    E4220001 While the ADF is in standby, the communication with its host machine is disrupted for 5 sec or more; or, while the ADF is in operation, the communication with its host machine is disrupted for 0.5 sec or more
    Saddle Finisher-G1 Error Codes
    E5010001The communication between the finisher controller PCB and the puncher drive PCB is disrupted
    E5050001 When the main power is turned on, the checksum of the finisher controller PCB has a fault
    0002 When the main power is turned on, the checksum of the puncher driver PCB has a fault
    E5100001 The feeding roller does not leave home position when the feed motor is driven for 2 sec
    0002 The feeding roller does not return to home position when the feed motor is driven for 2 sec
    E5140001 The delivery belt does not leave home position when the stack delivery motor is driven for 3 sec
    0002 The delivery belt does not return to home position when the stack delivery motor is driven for 3 sec
    E5300001 The aligning plate (rear) does not leave home position when the alignment motor (rear) is driven for 3 sec
    0002 The aligning plate (rear) does not return to home position when the alignment motor (rear) is driven for 3 sec
    E5310001The stapler does no leave home position when the stapler/folder motor is driven for 1.5 sec
    0002The stapler does not return to home position when the stapler/folder motor is driven for 1.5 sec
    0003The clock signal is disrupted for 1 sec or more while the stapler/folder motor is driven
    E5320001The stapler unit does not leave home position when the stapler slide motor is driven for 4.5 sec
    0002The stapler unit does not return to home position when the stapler slide motor is driven for 4.5 sec
    E5370001The aligning plate (front) does not leave home position when the alignment motor (front) is driven for 3 sec
    0002The aligning plate (front) does not return to home potion when the alignment motor (front) is driven for 3 sec
    E5400001The paper surface sensor remains unchanged 10 sec after the tray ascent/ descent motor is driven
    0002The tray upper sensor goes ON while the tray is moving up.
    0003The clock for the clock sensor is disrupted for 10 sec or more while the tray ascent/descent motor is driven
    E5770001The paddle does not leave home position when the paddle motor is driven for 2 sec or more
    0002The paddle does not return to home position when the paddle motor is driven for 2 sec or more
    0003The stack ascent/descent guide does not leave home position when the paddle motor is driven for 2 sec or more
    0004The stack ascent/descent guide does not return to home position when the paddle motor is driven for 2 sec or more
    E5900001The puncher does not return to home position when the puncher motor is driven for 250 msec
    0002The clock from the puncher motor clock sensor is disrupted for 60 msec or more when the puncher motor is driven
    E592 In the course of sensor output automatic adjustment, the light-receiving voltage is 2.5 V or less even when the light-emitting voltage is set to 4.4 V. In the course of output automatic adjustment, the light-receiving voltage is 2.5 V or more even when the light-emitting voltage is set to 0 V. In the course of sensor output automatic adjustment, the light-emitting voltage is set to 4.4 V or more
    0001 to 0005Horizontal registration sensor
    0006Puncher waste full sensor
    E5930001The puncher not leave home position when the puncher shift motor is driven for 1 sec
    0002The puncher does not return to home position when the puncher shift motor is driven for 1 sec
    E5F10001The folding roller does not leave home position when the stapler/folder motor is driven for 1.5 sec
    0002The folding roller does to return to home position when the stapler/folder motor is driven for 3.5 sec or more
    0003The clock is disrupted for 1 sec or more while the stapler/folder motor is driven
    Finisher-J1 Error Codes
    E5000000The communication between the copier and the finisher is disrupted and is not corrected for 5 sec or less
    E5140000 At the start of the motor CW operation, the stack handling motor (M2) may be driven for a specific number of rotations; however, the stack delivery lever home position sensor (S8) does not go ON
    E5300000 The alignment motor (M4) is driven for a specific number of rotations, but the aligning plate home position sensor (S7) does not go ON. The alignment motor (M4) is driven for a specific number of rotations, but the aligning plate home position sensor (S7) does not go OFF
    E5310000The stapling home position sensor (S16) does not go off 0.5 sec after the stapler motor is rotated CW. The stapling home position sensor (S16) dos not go ON with 0.5 sec after the stapler motor is rotated CW and, thereafter, the sensor does not go ON within 0.5 sec after the motor is rotated in reverse
    E5370000The aligning plate home position sensor (S6) does not go ON when the front alignment motor (M3) is driven for a specific number of rotations. The aligning plate home position sensor (S6) does not go OFF when the front alignment motor (M3) is driven for a specific number of rotations
    E5770000The return roller does not reach home position when the delivery motor (Ml) has been driven as much as will move it to the return roller home position sensor (S3)
    E5800000The delivery tray upper limit sensor (S13) goes ON while the delivery tray ascent/descent motor (M5) is in operation.
    The clock signal of the delivery tray ascent/descent motor clock sensor (S9) is not detected 15 times or more within 0.8 sec while the delivery tray ascent/ descent motor (M5) is in operation.
    The delivery tray paper height sensor (S10) does not go ON 4 sec after the delivery tray ascent/descent motor (M5) starts to move up.
    The delivery tray paper height sensor (S10) does not go OFF 4 sec after the delivery tray ascent/descent motor (M5) starts to move down
    E5850000 At the start of the motor CCW operation, the stack handling motor (M2) may be driven for a specific number of rotations; however, the stack delivery lever home position sensor (S8) does not go ON



    Коды ошибок мфу Canon iR 2200/2800/3300. Как сбросить ошибку.

    Главная | Каталог | Услуги | Наши клиенты | Контакты | Техподдержка | Полезная информация

    Rambler's Top100 Рейтинг@Mail.ru