|
|
|
|
| Коды ошибок Kyocera
FS-2020D, 3920DN, 4020DN |
|
| Код
ошибки |
Неполадки |
Причина |
Устранение |
| 0100 |
Backup memory device
error |
Defective
flash memory. |
Replace main PWB |
| |
|
Defective
main PWB. |
Replace main PWB |
| 0110 |
Backup memory data
error |
Defective
flash memory. |
Replace main PWB |
| |
|
Defective
main PWB. |
Replace main PWB |
| 0120 |
MAC address data
error |
Defective
flash memory. |
Replace
the engine PWB |
| |
|
Defective
engine PWB. |
Replace the engine PWB |
| 0150 |
Engine
PWB EEPROM error Detecting engine PWB EEPROM
communication error. |
Improper
installation engine PWB EEPROM. |
Check
the engine PWB EEPROM installation, Remedy. |
| |
|
Defective
engine PWB. |
Replace the engine PWB |
| 0170 |
Billing counting
error |
Defective
main PWB. |
Replace main PWB |
| 0420 |
Paper
feeder communication error Communication error between
engine PWB and optional paper feeder. |
Improper
installation paper feeder. |
Follow installation
instruction carefully again. |
| |
Defective
harness between connect-L PWB (YC2) and paper feeder interface connector, or
improper connector insertion. |
Reinsert
the connector. Also check for continuity within the connector harness. If
none, remedy or replace the harness. |
| |
|
Defective
harness between connect-L PWB (YC6) and engine PWB (YC504), or improper
connector insertion. |
Reinsert
the connector. Also check for continuity within the connector harness. If
none, remedy or replace the harness. |
| |
|
Defective
engine PWB. |
Replace the engine PWB |
| |
|
Defective
paper feeder. |
Replace the paper
feeder. |
| 1010 |
Lift
motor lock error *40/42 and 45/47 ppm printers (EUR/ USA
model) only A motor over-current signal is detected continuously for 5
seconds since the lift motor is activated. |
Defective
bottom plate elevation mechanism in the paper cassette. |
Check
to see if the bottom plate can move smoothly and repair it if any problem is
found. |
| |
Defective
lift motor drive transmission system. |
Check
if the gears rotate smoothly. If not, grease the bushings and gears. Check
for broken gears and replace if any. |
| |
|
Defective lift motor. |
Replace the lift
motor. |
| |
|
Defective
engine PWB. |
Replace
the engine PWB |
| 1140 |
Lift
motor ascent error *40/42 and 45/47 ppm printers (EUR/
USA model) only |
Defective
bulk paper feeder’s tray top position sensor. |
Replace
the bulk paper feeder’s tray top position sensor. |
| |
Optional bulk
paper feeder’s tray top position sensor does not turn on. Lift motor lock
error occurred 3 times. |
Defective
harness between bulk paper feeder’s tray top position sensor and main PWB
(YC6), or improper connector insertion. |
Reinsert
the connector. Also check for continuity within the connector harness. If
none, remedy or replace the harness. |
| |
|
Defective
bulk paper feeder’s main PWB. |
Replace
the bulk paper feeder’s main PWB. (Refer to bulk paper feeder’s service
manual) |
| 1150 |
Lift
motor descent error *40/42 and 45/47 ppm printers (EUR/
USA model) only Optional bulk paper feeder’s tray bottom position sensor does
not turn on. Lift motor lock error occurred 3 times. |
Defective
bulk paper feeder’s tray bottom position sensor. |
Replace
the bulk paper feeder’s tray bottom position sensor. |
| |
Defective
harness between bulk paper feeder’s tray bottom position sensor and main PWB
(YC8), or improper connector insertion. |
Reinsert
the connector. Also check for continuity within the connector harness. If
none, remedy or replace the harness. (Refer to bulk paper feeder’s service
manual) |
| |
|
Defective
bulk paper feeder’s main PWB. |
Replace
the bulk paper feeder’s main PWB. (Refer to bulk paper feeder’s service
manual) |
| 2000 |
Main
motor error MMOTRDYN signal does not go low within 2 s
after MMOTONN signal goes low. |
Defective
harness between main motor and engine PWB (YC501), or improper connector
insertion. |
Reinsert
the connector. Also check for continuity within the connector harness. If
none, remedy or replace the harness. |
| |
|
Defective
main motor drive transmission system. |
Check
if the rollers and gears rotate smoothly. If not, grease the bushings and
gears. Check for broken gears and replace if any. |
| |
|
Defective
main motor. |
Replace the main
motor. |
| |
|
Defective
engine PWB. |
Replace the engine PWB |
| 2200 |
Drum
motor error DMOTRDYN signal does not go low within 2 s
after DMOTONN signal goes low. |
Defective
harness between drum motor and engine PWB (YC11), or improper connector
insertion. |
Reinsert
the connector. Also check for continuity within the connector harness. If
none, remedy or replace the harness. |
| |
|
Defective
drum motor drive transmission system. |
Check
if the gears rotate smoothly. If not, grease the bushings and gears. Check
for broken gears and replace if any. |
| |
|
Defective
drum motor. |
Replace the drum
motor. |
| |
|
Defective
engine PWB. |
Replace the engine PWB |
| 4000 |
Polygon
motor (laser scanner unit) error POLRDYN signal does not
go low within 10 s after POLONN signal goes low. |
Defective
harness between polygon motor and main PWB (YC11), or improper connector
insertion. |
Reinsert
the connector. Also check for continuity within the connector harness. If
none, remedy or replace the harness. |
| |
|
Defective
harness between main PWB (YC12) and engine PWB (YC12), or improper connector
insertion. |
Reinsert
the connector. Also check for continuity within the connector harness. If
none, remedy or replace the harness. |
| |
|
Defective
laser scanner unit. |
Replace the laser scanner unit |
| |
|
Defective
engine PWB. |
Replace
the engine PWB |
| |
|
Defective
main PWB. |
Replace the main PWB |
| 4200 |
Laser
output (pin photo sensor) error The pin photo signal
(PDN) is not output within a specified time after the polygon motor ready
signal (POLRDYN) becomes ready (L level). |
Defective
harness between PD PWB (YC1) and main PWB (YC16), or improper connector
insertion. |
Reinsert
the connector. Also check for continuity within the connector harness. If
none, remedy or replace the harness. |
| |
|
Defective
APC PWB. |
Replace
the laser scanner unit |
| |
|
Defective
PD PWB. |
Replace the laser scanner unit |
| |
|
Defective
main PWB. |
Replace the main PWB |
| 5100 |
Short-circuited
main charger output Five pages have been printed with the
main charger output short-circuited. |
Drum
unit installed incorrectly. |
Verify
harness is not pinched in the drum unit. |
| |
Engine
PWB installed incorrectly. |
Verify
harness is not pinched in the engine PWB. |
| |
|
Defective
engine PWB. |
Replace the engine PWB |
| 6000 |
Broken
fuser heater lamp wire The temperature does not reach
100°C/ 212°F after the fuser heater lamp has been turned on continuously for
30 s. |
Poor
contact in the fuser thermistor 1 connector terminals. |
Reinsert the
connector |
| |
35/37 ppm printer (EUR/USA model): The temperature does not rise by
1°C/ 1,8°F after the fuser heater lamp has been turned on continuously for 5
s during printing. |
Fuser
thermistor 1 installed incorrectly. |
Check and reinstall if
necessary |
| |
Thermal
cutout triggered. |
Check for
continuity. If none, replace the thermal cutout |
| |
40/42 and 45/47 ppm printers (EUR/USA
model): The temperature does not rise by 1°C/ 1,8°F after the fuser heater
lamp has been turned on continuously for 10 s during warm-up or at standby. |
Fuser
heater lamp installed incorrectly. |
Check and reinstall if
necessary |
| |
Broken
fuser heater lamp wire. |
Check
for continuity. If none, replace the fuser heater lamp |
| 6020 |
Abnormally high fuser thermistor 2 temperature The temperature of the fuser thermistor 2 detects 240°C/464°F
or more continuously for 3 s. |
Shorted
fuser thermistor 2. |
Measure
the resistance. If it is 0 Q, replace the fuser thermistor 2 |
| |
Defective
engine PWB. |
Replace the engine PWB |
| 6030 |
Broken
fuser thermistor 2 wire Input from fuser thermistor 2 is
less than 1 (A/D value) for more than 1 s. |
Poor
contact in the fuser thermistor 2 connector terminals. |
Reinsert the connector |
| |
|
Broken
fuser thermistor 2 wire. |
Measure
the resistance. If it is 0 Om, replace the fuser
thermistor 2 |
| |
|
Fuser
thermistor 2 installed incorrectly. |
Check
and reinstall if necessary |
| |
|
Thermal
cutout triggered. |
Check for
continuity. If none, replace the thermal cutout |
| |
|
Fuser
heater lamp installed incorrectly. |
Check and reinstall if
necessary |
| |
|
Broken
fuser heater lamp wire. |
Check
for continuity. If none, replace the fuser heater lamp |
| 6120 |
Abnormally high fuser thermistor 1 temperature The temperature of the fuser thermistor 1 detects 240°C/464°F
or more continuously for 3 s. |
Shorted
fuser thermistor 1. |
Measure
the resistance. If it is 0 Om, replace the fuser thermistor 1 |
| |
Defective
engine PWB. |
Replace
the engine PWB |
| 6130 |
Broken
fuser thermistor 1 wire Input from fuser thermistor 1 is
less than 1 (A/D value) for more than 1 s. |
Poor
contact in the fuser thermistor 1 connector terminals. |
Reinsert the connector |
| |
|
Broken
fuser thermistor 1 wire. |
Measure
the resistance. If it is open replace the fuser
thermistor 1 |
| |
|
Fuser
thermistor 1 installed incorrectly. |
Check and reinstall if
necessary |
| 6220 |
Abnormally high fuser thermistor 3 temperature The temperature of the fuser thermistor 3 detects 250°C/482°F
or more continuously for 3 s. |
Shorted
fuser thermistor 3. |
Measure
the resistance. If it is 0 Om replace the fuser
thermistor 3 |
| |
Defective
engine PWB. |
Replace the engine PWB |
| 6230 |
Broken
fuser thermistor 3 wire Input from fuser thermistor 3 is
less than 1 (A/D value) for more than 1 s. |
Poor
contact in the fuser thermistor 3 connector terminals. |
Reinsert the connector |
| |
|
Broken
fuser thermistor 3 wire. |
Measure
the resistance. If it is open, replace the fuser
thermistor 3 |
| |
|
Fuser
thermistor 3 installed incorrectly. |
Check and reinstall if
necessary |
| 6400 |
Zero
cross signal error The ZCROSS signal does not reach the
engine PWB for more than 2 s. |
Defective
harness between connect-L PWB (YC8) and engine PWB (YC3), or improper
connector insertion. |
Reinsert
the connector. Also check for continuity within the connector harness. If
none, remedy or replace the harness. |
| |
|
Defective
connection between power source unit (YC103) and connect-L PWB (YC1). |
Reinsert the
connector. |
| |
|
Defective
power source unit. |
Replace the power source unit |
| |
|
Defective
engine PWB. |
Replace the engine PWB |
| 7000 |
Toner
motor lock error A motor over-current signal is detected
continuously for 5 seconds since the toner motor is activated. |
Lump
of toner inside toner container. |
Replace the toner
container. |
| |
Defective
toner replenishment drive system. |
Replace the developing unit |
| |
|
Defective
toner motor. |
Replace the developing unit |
| |
|
Defective
engine PWB. |
Replace the engine PWB |
| 7410 |
Drum
unit non- installing error The drum unit is not installed
or not installed properly. The drum PWB EEPROM does not communicate normally. |
The
drum unit is not installed. |
Install the drum unit |
| |
Defective
connection drum PWB (YC1) and connect-L PWB (YC3). |
Check
the connection of connectors drum PWB (YC1) and connect-L PWB (YC3). |
| |
|
Defective
drum PWB EEPROM. |
Replace the drum unit |
| |
|
Defective
engine PWB. |
Replace the engine PWB |
| FO F000 |
Communication problem between the main PWB and
operation panel PWB Communication is failed between the
operation panel PWB and the main PWB. |
Defective
main PWB. |
Turn
the power switch off/on to restart the printer.lf the error is not resolved,
replace main PWB |
| |
Defective
operation panel PWB. |
Replace the operation
panel PWB. |
| F010 |
Main PWB checksum
error |
Defective
main PWB. |
Turn
the power switch off/on to restart the printer.lf the error is not resolved,
replace main PWB |
| F020 |
Main
or expanded memory error Checksum failed with main memory
(RAM) on the main PWB or expanded memory (DIMM). |
Defective
system main memory (RAM) on the main PWB. |
Turn
the power switch off/on to restart the printer.lf the error is not resolved,
replace main PWB |
| |
|
Defective
expanded memory (DIMM). |
Replace the expanded memory
(DIMM) |
| F030 |
General
failure Miscellaneous failure with the main PWB. |
Defective
main-PWB. |
Turn
the power switch off/on to restart the printer.lf the error is not resolved,
replace main PWB |
| F040 |
Main
PWB - engine PWB communication error Communication
between main PWB and engine PWB is failed. |
Defective
harness between engine PWB (YC12) and main PWB (YC12), or improper connector
insertion. |
Reinsert
the connector. Also check for continuity within the connector harness. If
none, remedy or replace the harness. |
| |
|
Defective
main PWB. |
Turn
the power switch off/on to restart the printer.lf the error is not resolved,
replace main PWB |
| |
|
Defective
engine PWB. |
Replace the engine PWB |
| F050 |
Engine
PWB ROM checksum error A checksum error occurred with ROM
on the engine PWB. |
Some
error may have occurred when downloading the firmware of the engine PWB. |
Download
the firmware of the engine PWB again using the memory card |
| |
|
Defective
engine PWB. |
Turn
the power switch off/on to restart the printer. If the error is not resolved,
replace the EEPROM on the engine PWB or engine PWB |
| F186 |
Main PWB video data
control error |
Defective
main-PWB. |
Turn
the power switch off/on to restart the printer.lf the error is not resolved,
replace main PWB |
|
|
|
|
|
