|
|
|
|
|
|
|
Коды ошибок Kyocera FS-1120d,
1320d |
|
|
Код ошибки |
Неполадки |
Причина |
Устранение |
|
0150 |
Control
PWB EEPROM error Detecting control PWB EEPROM (U300)
communication error. |
Improper
installation control PWB EEPROM (U300). |
Check
the installation of the EEPROM (U300) and remedy if necessary |
|
|
|
Defective
control PWB. |
Replace the control PWB |
|
0420 |
Paper
feeder communication error Communication error between
control PWB and optional paper feeder. |
Improper
installation paper feeder. |
Follow installation
instruction carefully again. |
|
|
Defective
harness between control PWB (YC318) and paper feeder interface connector, or
improper connector insertion. |
Reinsert
the connector. Also check for continuity within the connector harness. If
none, remedy or replace the harness. |
|
|
|
Defective
control PWB. |
Replace the control PWB |
|
|
|
Defective
harness between PF main PWB (YC5) and paper feeder interface connector, or
improper connector insertion. |
Reinsert
the connector. Also check for continuity within the connector harness. If
none, remedy or replace the harness (Refer to the service manual for the
paper feeder). |
|
|
|
Defective
PF main-PWB. |
Replace
the PF main PWB (Refer to the service manual for the paper feeder). |
|
2000 |
Main
motor error The main motor ready input is not given for
2 s during the main motor is ON. |
Defective
harness between main motor (CN1) and control PWB (YC305), or improper
connector insertion. |
Reinsert
the connector. Also check for continuity within the connector harness. If
none, remedy or replace the harness. |
|
|
|
Defective
drive transmission system of the main motor. |
Check
if the rollers and gears rotate smoothly. If not, grease the bushings and
gears. Check for broken gears and replace if any. |
|
|
|
Defective main motor. |
Replace the main motor |
|
|
|
Defective
control PWB. |
Replace the control PWB |
|
2610 |
PF paper feed motor error (Paper feeder 1) The PF paper feed motor of paper feeder 1 ready input is not
given for 2 s during the PF paper feed motor is ON. |
Defective
harness between PF paper feed motor and PF main PWB (YC4), or improper
connector insertion. |
Reinsert
the connector. Also check for continuity within the connector harness. If
none, remedy or replace the harness (Refer to the service manual for the
paper feeder). |
|
Defective
drive transmission system of the PF paper feed motor. |
Check
if the gears rotate smoothly. If not, grease the bushings and gears. Check
for broken gears and replace if any. |
|
Defective
PF main motor. |
Replace
the PF main motor (Refer to the service manual for the paper feeder). |
|
Defective
control PWB. |
Replace the control PWB |
|
2620 |
PF paper feed motor error (Paper feeder 2) The PF paper feed motor of paper feeder 2 ready input is not
given for 2 s during the PF paper feed motor is ON. |
Defective
harness between PF paper feed motor and PF main PWB (YC4), or improper
connector insertion. |
Reinsert
the connector. Also check for continuity within the connector harness. If
none, remedy or replace the harness (Refer to the service manual for the
paper feeder). |
|
Defective
drive transmission system of the PF paper feed motor. |
Check
if the gears rotate smoothly. If not, grease the bushings and gears. Check
for broken gears and replace if any. |
|
Defective
PF main motor. |
Replace
the PF main motor (Refer to the service manual for the paper feeder). |
|
Defective
control PWB. |
Replace the control PWB |
|
4000 |
Polygon motor (laser scanner unit) error The polygon motor ready input is not given for 6 s during the
polygon motor is ON. |
Defective
harness between polygon motor and control PWB (YC319), or improper connector
insertion. |
Reinsert
the connector. Also check for continuity within the connector harness. If
none, remedy or replace the harness. |
|
Defective
laser scanner unit. |
Replace the laser scanner unit |
|
Defective
control PWB. |
Replace the control PWB |
|
6000 |
Broken
fuser heater lamp wire The fuser temperature does not
rise after the fuser heater lamp has been turned on. |
Poor
contact in the fuser thermistor connector terminals. |
Reinsert the connector |
|
|
Poor
contact in the fuser heater lamp connector terminals. |
Reinsert the connector |
|
|
|
Fuser
thermistor installed incorrectly. |
Replace the fuser unit |
|
|
|
Fuser
thermal cutout triggered. |
Replace the fuser unit |
|
|
|
Fuser
heater lamp installed incorrectly. |
Replace the fuser unit |
|
|
|
Broken
fuser heater lamp wire. |
Replace the fuser unit |
|
6020 |
Abnormally high fuser thermistor temperature Fuser thermistor detects abnormally temperature. |
Shorted
fuser thermistor. |
Replace the fuser unit |
|
|
Defective
control PWB. |
Replace the control PWB |
|
6030 |
Broken
fuser thermistor wire Input from fuser thermistor is 0
(A/D value). |
Poor
contact in the fuser thermistor connector terminals. |
Reinsert the connector |
|
|
|
Broken
fuser thermistor wire. |
Replace the fuser unit |
|
|
|
Fuser
thermistor installed incorrectly. |
Replace the fuser unit |
|
|
|
Fuser
thermal cutout triggered. |
Replace the fuser unit |
|
|
|
Fuser
heater lamp installed incorrectly. |
Replace the fuser unit |
|
|
|
Broken
fuser heater lamp wire. |
Replace the fuser unit |
|
6400 |
Zero
cross signal error The zero cross signal does not reach
the control PWB for specified time. |
Defective
harness between high voltage PWB (YC202) and control PWB (YC311), or improper
connector insertion. |
Reinsert
the connector. Also check for continuity within the connector harness. If
none, remedy or replace the harness |
|
|
|
Defective
harness between power source PWB (YC103) and high voltage PWB (YC201), or
improper connector insertion. |
Reinsert
the connector. Also check for continuity within the connector harness. If
none, remedy or replace the harness |
|
|
|
Defective
power source PWB. |
Replace the power source PWB |
|
|
|
Defective
control PWB. |
Replace the control PWB |
|
7990 |
Waste
toner full The waste toner sensor has detected that the
waste toner reservoir (drum unit) is full. |
Waste
toner reservoir (drum unit) is full. |
Turn
the main power switch off/on to restart the printer. If the error is not
resolved, replace the drum unit |
|
|
Defective
waste toner sensor. |
Replace the waste
toner sensor. |
|
|
|
Defective
control PWB. |
Replace the control PWB |
|
F010 |
Control PWB checksum
error |
Defective
code ROM (flash memory). |
Turn
the power switch off/on to restart the printer. If the error is not resolved,
replace the control PWB |
|
|
|
Defective
control PWB. |
Replace the control PWB |
|
F020 |
Control PWB RAM
checksum error |
Defective
main memory (RAM) on the control PWB. |
Turn
the power switch off/on to restart the printer. If the error is not resolved,
replace control PWB |
|
|
|
Defective
expanded memory (DIMM). |
Replace
the expanded memory (DIMM) |
|
F030 |
Control PWB general
failure |
Defective
control PWB. |
Turn
the power switch off/on to restart the printer. If the error is not resolved,
replace control PWB |
|
F040 |
Control
PWB engine communication error |
Defective
control PWB. |
Turn
the power switch off/on to restart the printer. If the error is not resolved,
replace control PWB |
|
F050 |
Control
PWB engine checksum error |
Some
error may have occurred when downloading the firmware of the control PWB. |
Download
the firmware of the control PWB again using the memory card |
|
|
|
Defective
control PWB. |
Turn
the power switch off/on to restart the printer. If the error is not resolved,
replace control PWB |
|
F226 |
Control
PWB video data control error |
Defective
control PWB. |
Turn
the power switch off/on to restart the printer. If the error is not resolved,
replace control PWB |
|
|
|
|
|
